ManualsIQvitals
Midmark Corporation · Vital Signs Monitors
Open your document
Open ↗
Midmark IQvitals Zone Transitioning from Linear Deflation to STEP Deflation Quick Reference Guide 0
Midmark IQvitals Zone User Guide 22-78-0002
Stuck? Start here
✅ Check the simple stuff first
- Make sure the patient is safe — swap in a backup unit if you need to.
- Reproduce the complaint yourself and write down exactly what you see (screen, alarm, code).
- Check power, battery, cables, accessories, and settings before ordering parts.
- Then open the service manual above and follow its troubleshooting section.
🛠️ Common faults for IQvitals (8)
NIBP Air Leak / Inflation too quick / Unable to determine NIBP source ↗
- Check cuff size and the hose for leaks and kinks
- Values must be within sys 50–260 / dia 20–210
NIBP accuracy suspect (Check Calibration) source ↗
- Set NIBP mode to Spot → Settings → More → password 1590 → Service mode
- T in a reference manometer with the cuff on a mandrel; test about 250/100/50 mmHg
- Pass within ±3 mmHg or 2%, plus the reference tolerance (e.g. 96–104 at 100)
Over-pressure protection check source ↗
- Inflate to 250 and squeeze the bulb on the pressure side
- Release must occur at 285–315 mmHg
Masimo SpO2 cable/sensor messages source ↗
- Replace an expired, defective or unrecognized cable or sensor
- Check Sensor Connection: reseat
Loss of SpO2/NIBP/LCD Comm. (high priority) source ↗
- Internal module link failure: remove from use; contact Midmark Technical Service for an RA
Battery absent/faulty, or Critical Battery at 10% source ↗
- Connect AC; if the battery is faulty, call service
Wireless or scale comm lost source ↗
- Re-pair the wireless device; check the Fairbanks or 625 table scale link
Annual maintenance source ↗
- Calibration check every 12 months
🔢 IQvitals error codes (13)
| Code | Meaning | Next step |
|---|---|---|
| NIBP Air Leak | Cuff or tubing leak | Check cuff and tubing connections source ↗ |
| Unable to determine NIBP | No reading, or pressure out of range (sys 50–260, dia 20–210) | Check connections and tubing for kinks source ↗ |
| Inflation too quick | Cuff/tubing connection issue | Check cuff and tubing source ↗ |
| Low Battery / Critical Battery | 40%/20% / 10% remaining | Connect power source ↗ |
| Battery is absent or faulty | Battery missing or bad | Call service source ↗ |
| Loss of SpO2 / NIBP / LCD Comm. | Internal module communication failure (high priority) | Service source ↗ |
| Loss of wireless pairing / Loss of wireless Comm. | Wireless device or board link lost | Re-pair the device source ↗ |
| Loss of Fairbanks scale / Chair Comm.; scale not functional | Scale module link failed | Check scale connection source ↗ |
| Unable to load configuration | Defaults in use | Reconfigure or service source ↗ |
| Cannot access patient info | Patient data inaccessible | Service source ↗ |
| Max number of patient records | Oldest records will be overwritten | Export or delete records source ↗ |
| Cable/Sensor Life Expired, Incompatible, Unrecognized, Defective (Masimo) | SpO2 accessory problem | Replace the cable or sensor with a compatible one source ↗ |
| Interference Detected / Sensor Off patient | Light or motion interference, or sensor off | Reapply and shield the sensor source ↗ |
🧰 Common checks for Vital Signs Monitors (2)
Won't power on source ↗
- Confirm AC cord/outlet and battery charge
- Check internal power/battery harnesses
- Measure power supply output against spec (15 V DC on Welch Allyn Connex and Philips VS3)
- Charge battery fully; replace if still empty
Touchscreen issues source ↗
- Check whether touch is disabled/locked
- Calibrate touchscreen
- Check touchscreen cables before replacing parts
📞 Still stuck? Call Midmark Corporation
Midmark Corporation support ↗Missing a manual, code, or fix for this model? Tell us.